What does 10B-FB mean in COMPUTING
10B-FB stands for 10BASE-FB, which is a type of information technology networking cable. This type of network connection was phased out in favour of newer and more reliable technologies, but was once the default form of connecting computers in local networks. 10BASE-FB stands for “10 megabits per second (Mbps) over fibre optics”. It is also sometimes referred to as “twisted pair with fibre optics”.
10B-FB meaning in Computing in Computing
10B-FB mostly used in an acronym Computing in Category Computing that means 10BASE-FB
Shorthand: 10B-FB,
Full Form: 10BASE-FB
For more information of "10BASE-FB", see the section below.
Advantages Of 10BASE-FB
The main advantages of using 10BASE-FB compared to other networking technologies are its high data transfer rates and low interference levels due to its use of optical fibres rather than copper cables. It is also relatively cheap compared to other fibre optic cable solutions, making it appealing to those on a budget or with smaller networks. Furthermore, its wide range makes it suitable for use in larger networks as well as small ones where distance could be an issue with other types of connections. Lastly, due to its protected wiring, it has lower signal interference than most other types of networking cables, resulting in less errors during data transfer and fewer dropouts while connected devices run their applications.
Disadvantages Of 10BASE-FB
The main disadvantage of using 10 BASE-FB is that it is not compatible with many current types of networking hardware such as routers or switches because they need higher transmission speeds like 100Mbps or 1Gbps in order to function properly. Another disadvantage is that due to its complexity setting up 10 BASE-FB networks can be quite difficult and time consuming compared to other more user friendly technologies such as Wi-Fi which allow users a much quicker setup time without relying on specialised hardware like networking cables or patch panels. Finally, although cheaper than some other forms of fibre optic cabling solutions theirs are still relatively expensive upfront costs associated with them when compared against more common networking solutions such as Cat5 cables or Wi-Fi routers.
Essential Questions and Answers on 10BASE-FB in "COMPUTING»COMPUTING"
What is 10BASE-FB?
10BASE-FB stands for 10 Mbps baseband fiber optic. It is an Ethernet network standard that uses fiber optics as the transmission medium. It operates at a data rate of 10 Mbps, using 8B/10B line coding, and is commonly used for short-distance applications such as between wiring closets or between buildings on a corporate campus.
Why is 10BASE-FB used?
10BASE-FB is used to provide reliable and secure connections by eliminating the interference problems associated with traditional copper wires in environments where physical security or electromagnetic interference is an issue. As an additional advantage, it supports longer distances than other Ethernet varieties, making it suitable for distributed networks which span multiple buildings over large distances.
Is there anything unique about connecting 10BASE-FB networks?
Yes. In addition to needing fiber cables and optical transceivers, you also need external repeaters when daisy-chaining multiple devices in order to maintain signal integrity and prevent packet loss due to attenuation.
How does the 8B/10B line coding work?
8b/10b line coding ensures that only valid sequences of 1`s and 0`s are sent across the link, allowing the receiver to decode the incoming data stream without errors. Specifically, it encodes each eight bit byte into a ten bit code word with two extra bits added as "parity" so that there are always 5 ones and 5 zeroes in each code word transmitted over the link.
How fast can 10BASE-FB transfer data?
The data rate of 10BASE-FB is 10 Mbps (Megabits per second). This means that it can transfer up to 1 megabyte (MB) of data per second or 8 megabits (Mb) of data per second under certain conditions.
Is it possible to upgrade an existing system to use 10BASE-FB?
Yes, it is possible to upgrade existing systems from copper wire networks to fiber optic networks by replacing copper wires with fiber cables and installing optical transceivers at both ends of the cable connection. However, you may need additional equipment such as repeaters or media converters for more complex topologies or longer cable distances.
What types of cables can be used in a 10 BASE FB network?
Generally speaking any type of multi mode fiber optic cable should be compatible with this standard like OM1, OM2, OM3/OM4 and OS2 Standards. Single Mode Fiber may also be used but additional equipment would be needed such as media converters or WDM devices depending on your specific setup requirements.
Are there any special network design considerations for a 10 BASE FB network?
Yes, one important consideration when designing a network with this technology is its distance limitation which can vary according to several factors like cable type, type of transceiver being used etc., Also keep in mind that if you plan on daisy chaining multiple devices then you will need external repeaters for signal integrity purposes.
Final Words:
Overall, although no longer used extensively due mainly through incompatibility issues arising from modern equipment such as routers and switches needing higher bandwidths than what's supported by this type of technology; if you have an older network that requires very fast data transfer rates across short distances at reasonable cost then 10 BASE FB may still provide a viable solution if all hardware components are compatible with each other. Therefore if you have an older system set up then investigating this option may be worthwhile before replacing equipment unnecessarily just because new technologies exist offering better performance than what's available through this medium.